Milk cooling tanks MP Powertank

MP Powertank
(MPP 1.000 - 14.000lt & MPPO 10.000 - 20.000lt)

01

The MP Powertank milk cooling tank series is the leading solution for milk cooling in medium and large livestock and dairy units. They are horizontal type stainless steel tanks with access manholes and automated systems for washing and disinfection after every emptying.

MP Powertank tanks are available in 16 capacities, round type from 1,000lt to 14,000lt and elliptical from 10,000 to 20,000lt. All models are constructed in such a way as to allow agitation of even small quantities of milk and exclude any possibility of ice formation.

  1. Dimensions
  2. Features
  3. Photos
  4. Video
  5. Washing Systems
1.000lt - 14.000lt

The round type MPP milk cooling tanks are available in 13 different models with capacities from 1,000lt to 14,000lt with one or two cooling units to meet the needs for 2-6 milkings.


dimensions powertank 1000 14000

powertank 1000 14000

10.000lt - 20.000lt

The elliptical type MPP Oval milk cooling tanks are available in 6 different models with capacities from 10,000lt to 20,000lt and are suitable for large dairy units due to the large surface of the evaporator which allows faster cooling of large quantities of milk and while they are easily installed in places where there is a height limitation. Depending on the needs, they can be equipped with more than two cooling systems.


dimensions powertank 10000 20000

powertank 10000 20000

*The precise height varies depending on the slope of the tanks W: 380mm for MPP Standard, W: 560mm for MPP Control, D: 180mm without expansion valves and D: 500mm with expansion valves.

Cooling unit

These series models are available in versions of 2, 4 or 6 milkings and can be equipped with 1, 2 or 4 cooling units providing strong cooling and reliability. For models up to 5,000lt it is possible to install the cooling unit on the tank. They are available with Tecumseh, Maneurop and Copeland compressors. For their protection and better performance, the circuit is equipped with: a solenoid valve, separate pressure switches to control high and low pressure of the cooling circuit, a pressure switch to control the second fan, a filter, a receiver bottle for the freon, a safety valve on the receiver, an expansion valve of appropriate power, separate thermomagnetic switches installed on the power circuit for each compressor and a voltage controller.

Insulation

All models are made entirely of stainless steel AISI 304 and are optimally insulated with polyurethane foam ensuring that a few minutes operation of the cooling unit is sufficient to preserve the pre-cooled milk.

Stainless steel external pressure equalizer

The stainless steel filter of the tanks prevents air entrapment inside the tank during its filling and facilitates drainage. Depending on the size of the tank, there can be up to three filters that can be easily removed.

Measuring dipstick

All MP Powertank models are equipped with a stainless steel measuring dipstick and a conversion table in liters for easy calculation of the quantity of milk.

Agitation motor

The MP Powertank milk cooling tanks are equipped with powerful motors made by the French company Sirem, set to 21-25 rpm and placed on an elevated base to ensure easy cleaning. Tanks from 8,000 to 20,000 lt have two or three motors for better agitation of the quantity of milk.

Manhole

The stainless steel manhole of the tanks provides superior sealing without the use of a flange. It is of a Φ400mm diameter for models up to 3,000lt and Φ500mm for models up to 4,000lt. It is fully rotatable and its smart design allows it to be held in the open position.

Ladder

All models over 1,500lt have a stainless steel ladder with anti-slip steps for the inspection of the milk content through the manhole at the top of the tank.

Milk inlet

The MP Powertank cooling tanks have 1 or 2 milk inlets of Φ76mm diameter. They are sealed with a stainless steel cap for the protection of the content of the tank.

Milk outlet

For models up to 6,000lt, a stainless steel butterfly valve, DN50 or SMS51 type, is used for milk outlet. For larger models, valve DN80 or SMS76 type is used. In all cases, adaptation to specific needs is possible.

Temperature sensor

The position of the temperature sensor has been carefully selected so that it is easily replaced in case of failure.

Stainless steel adjustable legs

The MP Powertank tanks have 4 to 12 support legs, depending on the model, all height adjustable, for proper alignment even on uneven floors.

Self-cleaning valve (optional)

A self-cleaning valve can optionally be installed to assist the use of the tanks' washing system.

Electronic measuring system (optional)

A high-precision electronic measuring system with the use of a sensor- float can be installed for a reliable control of the quantity of milk inside the tank. The panel of the system has a large easy-to-read 5-digit display indicating the quantity of milk in kilograms or liters.

Two systems are provided for the control of the cooling and washing functions of the MP Powertank tanks:


  MPP Standard washing system   MPP Control washing system